Exam : CENP PW0-205
Title : certified wireless analusis professional(cwap)

1. When an access point sends an RTS frame, the duration field will contain an amount of time, measured in microseconds, equal to which of the following?
A. 2 ACK, 1 RTS, 1 DATA, 4 SIFS
B. 1 ACK, 1 CTS, 1 DATA, 3 SIFS
C. 1 DATA, 1 RTS, 2 SIFS, 1 DIFS, 1 ACK
D. 1 RTS, 1 CTS, 1 DATA, 2 ACK, 4 SIFS
Answer: B

2. Which of the following descriptions accurately describes IEEE 802.11 compliant Power Save mode operation in a DCF Basic Service Set?
A. Following a period of time in a low power state, client stations wake themselves and automatically poll the access point for traffic using a PS-Poll frame.
B. When the access point’s buffer is full, the access point wakes all client stations using a PS-Poll frame so that they can receive the data.
C. Upon receiving traffic for a dozing station, the access point wakes the client station using a PS-Poll frame so that the client station can receive the data.
D. After waking from a low power state, client stations listen for the next beacon to determine if sending a PS-Poll frame to the access point is necessary.
E. After waking at a schedule TBTT, client stations automatically send Null Function frames to the access point with the Power Management bit cleared.
Answer: D

3. A wireless network administrator has examined the frame retry counts on several client stations in a WLAN that is not using encryption, and has determined that they are extraordinarily high. For this reason, he has decided to configure station fragmentation thresholds to 400 bytes. With this configuration change, when a data frame with a 1500 byte MSDU is transmitted by one of the wireless client stations to a wired station through an access point, what will be the order and size (in bytes) of the fragments as they’re transmitted?
A. Frame1 = 400, Frame2 = 400, Frame3 = 400, Frame4 = 300
B. Frame1 = 300, Frame2 = 300, Frame3 = 300, Frame4 = 300, Frame5 = 300
C. Frame1 = 300, Frame2 = 400, Frame3 = 400, Frame4 = 400
D. Frame1 = 400, Frame2 = 400, Frame3 = 400, Frame4 = 400, Frame5 = 40
E. The fragmentation threshold setting on client stations only affects received frames, not transmitted frames
F. The fragmentation threshold setting on client stations is not a manual adjustment, and can only be auto-configured by access points
Answer: D

4. Which of the following is true regarding frame acknowledgement in an 802.11 wireless LAN?
A. ACK frames following Data fragments set the NAV of competing stations for a duration equal to two SIFS plus the next Data fragment and its ACK.
B. A client station reassociation request frames are only acknowledged with a reassociation response from the access point when roaming in a wireless LAN secured with 802.1X/EAP.
C. Probe request acknowledgement (sending of a probe response) is configurable in the access point and is always linked to SSID broadcast configuration in Beacons.
D. Beacon frames are acknowledged by all client stations configured for PCF mode.
E. Frame fragments are acknowledged individually (with an ACK frame)
F. In PCF mode, WEP-Data frames are only acknowledged by client stations, never by access points.
Answer: AE

5. The Timestamp field, found in 8011 Beacon Management frames, is 8 bytes in length and serves which of the following purposes?
A. Keeps all client stations in a BSS synchronized to within approximately 4 microseconds of the access point.
B. Allows client stations in the IBSS to pick the best of multiple beacons.
C. Used to notify client stations using power management features of how long their queued frames have been held by the access point.
D. Informs associating client stations how often to expect Beacon Management frames to be sent by the access point.
E. Allows all client stations in a BSS to calculate how long it took for the Beacon Management frame to traverse the wireless medium.
Answer: AB

6. An 802.11b client station, sends a single 600 byte MSDU to another 802.11b client station while operating as part of an unsecured infrastructure BSS. Due to thresholds set on all client stations and the access point, all MPDUs over 300 bytes in length invoke the RTS/CTS protocol. How many individual CTS frames are transmitted on the wireless medium as part of the entire process of moving the 600 byte MSDU between the two client stations?
A. 1
B. 2
C. 3
D. 4
Answer: B

7. Choose the true statements regarding wireless network discovery processes for an 802.11b network.
A. Client stations may continually send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner, regardless of their association state.
B. Access points send Beacon Management frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner including the channel for which the access point is configured.
C. Client stations send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner until they associate with an access point. After associating to an access point, they are no longer allowed to transmit Probe Request frames.
D. Access points send Beacon Management frames only on the 802.11b channel in the 2.4 GHz ISM band for which the access point is configured.
E. Client stations send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner until they receive at least 3 Probe Response frames.
Answer: AD

8. Which is true of the Association Identifier (AID) used in 802.11 wireless LANs?
A. The AID has a maximum value of 2048, and is used to uniquely identify a wireless client station associated with an access point.
B. The AID has a maximum value of 2007, and resides in the duration/ID field of a PS-Poll frame only.
C. When bit 16 of the field is zero, the value in bits 15-0 represent the remaining duration of a frame exchange.
D. The least significant 8 bits of this field are used by the wireless client station to identify which bit in a TIM indicates that the access point has frames buffered for the wireless client station.
E. The AID is used by the access point in DCF mode to reduce duplicate transmissions when sending multicasts.
Answer: B

PassQuick PW0-205 Practice Exams Description

Exam Number/Code: PW0-205

Exam Name: certified wireless analusis professional(cwap)

VUE Code: PW0-205

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-205 exam? Searching PW0-205 Braindumps, CWNP PW0-205 Test Questions, PW0-205 Practice Exam, PW0-205 Dumps? PassQuick PW0-205 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-205 Dumps is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

CWNP PW0-205 Exam

PassQuick PW0-200 Practice Exams Description

Exam Number/Code: PW0-200

Exam Name: certified wireless security professional(cwsp)

VUE Code: PW0-200

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-200 exam? Searching PW0-200 Braindumps, CWNP PW0-200 Test Questions, PW0-200 Practice Exam, PW0-200 Dumps? PassQuick PW0-200 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-200 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Free PassQuick PW0-200 Practice Engine Demo Download

Download CWNP PW0-200 Pdf Exam

　
　
Exam : CENP PW0-200
Title : Certified Wireless Security Professional(CWSP)

1. Given: ABC Corporation is selecting a security solution for their new WLANand a PPTP VPN is their first consideration because it is included with both server and desktop operating systems. While the 128-bit encryption of Microsoft’s MPPE is considered strong enough to adhere to corporate security policythe company is worried about security holes in MS-CHAPv2 authentication.
As a consultantwhat do you tell ABC Corporation about implementing MS-CHAPv2 authentication in a PPTP VPN?
A. MS-CHAPv2 is compliant with WPA-Personalbut not WPA2-Enterprise.
B. MS-CHAPv2 is subject to offline dictionary attacks.
C. MS-CHAPv2 is only secure when combined with WEP.
D. MS-CHAPv2 is only appropriate for WLAN security when used inside a TLS-encrypted tunnel.
E. MS-CHAPv2 uses anonymous Diffie-Hellman authenticationand is therefore secure.
F. MS-CHAPv2 can be replaced with EAP-TLS as the authentication mechanism for PPTP.
Answer: BDF

2. Given: ABC Company’s ERP WLAN has worked perfectly for the last 6 months. One morningnone of the company’s 10 users can connect to the company’s only access point. When the administrator logs into the access pointthere are hundreds of users associated using Open System authentication.
What is the problem?
A. The AP has been the victim of an RF DoS attack.
B. The AP has experienced an AP spoofing attack from a rogue AP.
C. The AP firmware has been corrupted and is erroneously reporting the number of users.
D. The AP has experienced an association flood attack.
Answer: D

3. During 802.1X/LEAP authenticationwhat authentication credential is passed using clear text across the wireless medium?
A. Password
B. x.509 certificate
C. Username
D. PAC
E. Shared secret
Answer: C

4. What happens in a bit flipping attack against an IEEE 802.11 device?
A. An attacker captures an encrypted framemodifies the ciphertextmodifies the ICV to hide the change to the ciphertextand then transmits the frame to appear as if it is from the original source.
B. An attacker uses a non-linear Message Integrity Check (MIC) on his computer to form a wireless crossover connection with the target computer.
C. An attacker injects data into a wireless transmission that results in a memory access exception at the target system for the purpose of breaching security.
D. An attacker sends each frame with the first bit alternating between 0 and 1causing the target computer to disable encryption synchronization.
E. An attacker captures an encrypted authentication frameand then executes a cracking algorithm against each 0 and 1 in the frame. After the frame is crackedit is used to authenticate the attacker’s computer.
Answer: A

5. In this diagram illustrating an example of the IEEE 802.11 standard’s 4-Way Handshakewhat is the purpose of the ANonce and SNonce?
A. They are used to pad Message 1 and Message 2 so there is no empty space in the frame.
B. The IEEE 802.11 standard requires that all cryptographic frames contain a nonce for security purposes.
C. They are added together and used as the GMKfrom which the GTK is derived.
D. They are values used in the derivation of the Pairwise Transient Key.
Answer: D

6. Given: You have a laptop computer with an integrated Wi-Fi compliant MiniPCI card.
What statements describe the limited effectiveness of locating rogue access points using WLAN discovery software such as NetStumblerKismetor MacStumbler?
A. Discovery tools like those listed cannot determine the authorization status of an access point.
B. A laptop computer can only be in one location at a time.
C. Discovery tools like those listed cannot determine if an access point is attached to a wired network.
D. Rogue access points using non-IEEE 802.11 frequency bands or unpopular modulations are not detected.
E. When data encryption in useaccess points cannot be detected using discovery tools like those listed.
Answer: ABCD

7. What policies would prevent peer-to-peer attacks against wireless-enabled corporate laptop computers when the laptops are also used on public access networks such as wireless hotspots?
A. Require managed personal firewall software on each laptop.
B. Require secure applications such as POP3/SHTTPSand SSH2.
C. Require VPN software for connectivity to the corporate network.
D. Require WPA2-Enterprise as the minimal WLAN security solution.
E. Require Port Address Translation (PAT) on each laptop.
F. Require a managed wireless endpoint security agent on each laptop.
Answer: ABCF

8. What WIPS parameter is configured to generate notifications?
A. Mobile unit density violations
B. Admission control status
C. Sensor sensitivity levels
D. Policy threshold values
Answer: D

9. Joe’s new laptop is experiencing difficulty connecting to ABC Company’s 802.11 network. The company’s wireless network administrator assured Joe that his laptop was authorized in the WIPS for connectivity to all Marketing department APs before it was given to him yesterday. The WIPS termination policy is shown in the exhibit.
What are some possible reasons that Joe cannot connect to the network?
A. Joe disabled his laptop’s integrated 802.11 radio and is using a personal PC card radio because of its updated chipsetdriversand client utilities.
B. Joe’s integrated 802.11 radio is sending too many Probe Request and EAPoL Start frames due to a corrupted driver.
C. Joe’s radio card has associated to an access point belonging to a neighboring 802.11 WLAN because it was configured to connect to any wireless network.
D. An ASLEAP attack has been detected on APs to which Joe’s laptop was trying to associate. The WIPS responded by disabling the APs.
E. Joe configured his 802.11 radio card to transmit at 100 mW to increase his SNR. The WIPS is detecting this much output power as a DoS attack.
F. Joe changed the system time on his computerand the WIPS is detecting this as a usage time violation.
Answer: AC

10. Given: ABC Company has a WLAN controller with three access points15 client devicesand uses WPA2-Personal for WLAN security.
What statement about ABC Company’s WLAN security is true?
A. Intruders may obtain the passphrase with an offline dictionary attack and gain network accessbut will be unable to decrypt data traffic.
B. Traffic injection attacks are possible because the transmitter lacks frame numbering.
C. An unauthorized wireless client device cannot associatebut can eavesdrop on some data because WPA2-Personal does not encrypt broadcast traffic.
D. An authorized WLAN user with a protocol analyzer can decode data frames of other authorized users if he captures that user’s 4-Way Handshake.
E. Because WPA2-Personal uses Open System authentication followed by a 4-Way Handshakehijacking attacks are easily performed.
Answer: D

11. Given: A network security auditor is assessing an IEEE 802.11 network’s exposure to security holes.
What task would save the most time if performed before the audit?
A. Identify the IP subnet information for each network segment.
B. Identify the manufacturer of the wireless intrusion prevention system.
C. Identify the skill level of the wireless network security administrator(s).
D. Identify the manufacturer of the wireless infrastructure hardware.
E. Identify the wireless security solution(s) currently in use.
Answer: E

12. Given: John Smith often works from home and wireless hotspots rather than commuting to the office. His laptop connects to the office network over IEEE 802.11 WLANs.
To safeguard his datawhat wireless security policy items should be implemented?
A. Use an IPSec VPN for remote connectivity
B. Use an HTTPS captive portal for authentication at hotspots
C. Use personal firewall software on his laptop
D. Use a protocol analyzer on his laptop to monitor for risks
E. Use 802.1X/PEAPv0 to connect to the corporate office network
Answer: AC

Recommended Training about CWNP PW0-200 testing Fromat

The following courses are the recommended training for PW0-200 PDF Fromat.

PW0-200 Q & A with Explanations

PW0-200 Audio video download

PW0-200 Study Guide materials

PW0-200 Preparation Labs

PW0-200 paper books

PW0-200 rapidshare 4shared sadikhov links

PW0-200 torrent notes

PW0-200 TestInside

PW0-200 sample print pdf version

Why do you Choose PassQuick PW0-200 Test Engine?

Quality and Value for the PW0-200 Exam

PassQuick Practice Exams for CWNP Certification PW0-200 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass PW0-200 Exam

If you prepare for PW0-200 exam using our PassQuick exams, we guarantee your success in the first attempt. If you do not pass the PW0-200 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

PassQuick PW0-100 Practice Exams Description

Exam Number/Code: PW0-100

Exam Name: certified wireless network administrator(cwna)

VUE Code: PW0-100

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-100 exam? Searching PW0-100 Braindumps, CWNP PW0-100 Test Questions, PW0-100 Practice Exam, PW0-100 Dumps? PassQuick PW0-100 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-100 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Free PassQuick PW0-100 Practice Engine Demo Download

Download CWNP PW0-100 Pdf Exam

　
　
Exam : CENP PW0-100
Title : certified wireless network administrator(cwna)

1. What are some common specifications for 802.11 WLAN antennas?
A. Spectral Purity Rating
B. Frequency Range in MHz
C. Impedance in Ohms
D. VSWR Rating
E. Return Loss Rating
F. Polarization
Answer: BCDF

2. What is a valid type of lightning arrestor used with 802.11 wireless LANs?
A. Coaxial arrestor with a metal oxide varistor (MOV) input circuit
B. Parallel tuned tank-circuit arrestor
C. Coaxial arrestor with a gas discharge tube
D. Inductor-based load-sensing arrestor
Answer: C

3. Given: ABC University provides wireless access to campus buildings from their Data Center building. ABC has installed a tower on the Data Center building with a sectorized omnidirectional antenna array using 90 of horizontal beamwidth per sector.
What is the next step in configuring the antenna array?
A. Calculate Earth Bulge into the System Operating Margin (SOM).
B. Configuring the downtilt of each antenna in the array.
C. Providing DC power to each antenna in the array.
D. Adjusting each antenna’s beamwidths for optimal gain.
Answer: B

4. What word describes an RF signal that bounces off a smooth or coated surface and changes direction?
A. Diffraction
B. Reflection
C. Refraction
D. Diffusion
E. Scattering
Answer: B

5. What factors affect the propagation distance of an RF signal?
A. Antenna gain
B. Receiving station sensitivity
C. Fresnel zone blockage
D. Power over Ethernet (PoE) usage
E. Antenna polarization
F. Link budget calculations
Answer: AC

6. Given: XYZ Corporation is experiencing connectivity problems with their existing building-to-building bridge link. A brick wall on the roof of one building is partially blocking the Fresnel Zone, and the connection is dropping many frames. The administrator moves the antenna to an area not obstructed by the brick wall and then realizes the RF cable cannot reach the new location.
If an RF extension cable is used, what are the likely results?
A. The data throughput rate will increase because VSWR will decrease.
B. The Equivalent Isotropically Radiated Power (EIRP) will decrease.
C. The antenna coverage area will decrease.
D. The return loss will increase unless the impedance of the RF extension cable is equal to 50% of the antenna impedance.
E. The likelihood of a direct lightning strike will increase, placing the entire WLAN system at risk.
Answer: BC

7. Given: A wireless LAN transmitter that emits a 100 mW signal is connected to a cable with a 3 dB loss. If the cable is connected to an antenna with a 10 dBi gain, what is the EIRP at the antenna element?
A. 50 mW
B. 250 mW
C. 500 mW
D. 750 mW
E. 1000 mW
Answer: C

8. What phrase describes the effect of increasing the distance that an RF wave travels when the RF antenna lobe is focused in a desired direction?
A. Polar Extension
B. Active Amplification
C. Beam Compression
D. Passive Gain
E. Phased Array Propagation
Answer: D

9. In a long-distance RF link, what statement about Fade Margin is true?
A. Fade Margin is the amount of signal strength in addition to the Link Budget.
B. The Fade Margin of a long-distance RF link does not account for antenna gain.
C. Fade Margin is rarely taken into account on a long-distance RF link.
D. Fade Margin and Jamming Margin are synonymous, interchangeable terms.
Answer: A

10. While working on a presentation document in a conference room equipped with a wireless network, you notice that, as you turn your laptop in different directions, your wireless signal strength changes. What RF signal property is primarily responsible for this change in signal strength?
A. The RF signal’s amplitude is changing due to a change in the visual line-of-sight.
B. The RF signal’s wavelength is being affected by varying antenna gain.
C. The RF signal’s multipath is changing the amount of RF absorbed by nearby objects.
D. The RF signal’s phase is oscillating due to electromagnetic interference (EMI).
E. The RF signal’s polarization is different than the receiving antenna.
Answer: E

11. Which units of measure are used to describe a calculable power quantity?
A. dB
B. dBm
C. dBi
D. mW
E. RSSI
F. dBd
Answer: BD

12. What causes an excessive Voltage Standing Wave Ratio (VSWR) in an 802.11a WLAN?
A. Mismatched impedance between devices in series with the main RF signal
B. Reflected DC current on the main RF signal line
C. Scattered RF signal along the main signal path
D. Inductance (crosstalk) between adjacent conductors
Answer: A

Recommended Training about CWNP PW0-100 testing Fromat

The following courses are the recommended training for PW0-100 PDF Fromat.

PW0-100 Q & A with Explanations

PW0-100 Audio video download

PW0-100 Study Guide materials

PW0-100 Preparation Labs

PW0-100 paper books

PW0-100 rapidshare 4shared sadikhov links

PW0-100 torrent notes

PW0-100 TestInside

PW0-100 sample print pdf version

Why do you Choose PassQuick PW0-100 Test Engine?

Quality and Value for the PW0-100 Exam

PassQuick Practice Exams for CWNP Certification PW0-100 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass PW0-100 Exam

If you prepare for PW0-100 exam using our PassQuick exams, we guarantee your success in the first attempt. If you do not pass the PW0-100 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

PassQuick PW0-104 Practice Exams Description

Exam Number/Code: PW0-104

Exam Name: Wireless LAN Administration Exam

VUE Code: PW0-104

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-104 exam? Searching PW0-104 Braindumps, CWNP PW0-104 Test Questions, PW0-104 Practice Exam, PW0-104 Dumps? PassQuick PW0-104 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-104 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Free PassQuick PW0-104 Practice Engine Demo Download

Download CWNP PW0-104 Pdf Exam

　
　
Exam : CWNP PW0-104
Title : Wireless LAN Administration Exam

1. In a long-distance RF link, what statement about Fade Margin is true?
A. Fade Margin is an amount of signal strength in addition to the Link Budget.
B. The Fade Margin of a long-distance RF link does not account for antenna gain.
C. Fade Margin is rarely taken into account on a long-distance RF link.
D. Fade Margin and Jamming Margin are synonymous, interchangeable terms.
Answer: A

2. What causes an excessively high Voltage Standing Wave Ratio (VSWR) in an 8011 WLAN?
A. An impedance mismatch between devices in series with the main RF signal
B. Reflected DC voltage on the main RF signal line
C. Refracted RF signal peaks along the main signal path
D. Crosstalk (inductance) between adjacent conductors
Answer: A

3. Which units of measure are used to describe relative power level changes?
A. dBm
B. dBi
C. dB
D. mW
E. dBW
Answer: BC

4. As an RF wave propagates through space, the wave front experiences natural expansion. What is the detrimental effect of this expansion in a WLAN system?
A. Linear Diffusion Loss
B. Signal Attenuation
C. Transmission Obfuscation
D. Fresnel Zone Thinning
E. Azimuth Inflation
Answer: B

5. What factor is NOT taken into account when calculating the System Operating Margin of a point-to-point outdoor WLAN bridge link?
A. Operating frequency
B. Tx antenna gain
C. Tx power
D. Rx cable loss
E. Antenna height
F. Rx sensitivity
G. Distance
Answer: E

6. What word describes the bending of an RF signal as it passes between mediums of different density?
A. Diffraction
B. Reflection
C. Refraction
D. Diffusion
E. Scattering
Answer: C

7. Given: A WLAN transmitter that emits a 200 mW signal is connected to a cable with a 9 dB loss.
if the cable is connected to an antenna with a 10 dBi gain, what is the EIRP at the antenna element?
A. 50 mW
B. 250 mW
C. 500 mW
D. 750 mW
E. 1000 mW
Answer: B

8. Given: ABC Company’s network administrator was just asked to install a 5 GHz OFDM bridge link between two buildings. He connected a WLAN bridge with a 50-ohm output to a 50-ohm RF coaxial cable. He connected the other end of the RF coaxial cable to a 25-ohm, 6 dBi Yagi antenna.
What is the maximum VSWR between the WLAN bridge and the Yagi antenna?
A. 1.0:1
B. 1.1:1
C. 1.2:1
D. 1.5:1
E. 2.0:1
F. 1.0:2
Answer: E

9. Given: Return Loss is the decrease of forward energy in a system because some of the power is being reflected back toward the transmitter.
What can cause a high return loss in an RF transmission system?
A. A Voltage Standing Wave Ratio (VSWR) of 1.5:1
B. An impedance mismatch between devices in the RF system
C. Cross-polarization of the RF signal as it passes through the RF system
D. The use of multiple connector types in the RF system (e.g. N-type and SMA-type)
E. Low output power at the transmitter and use of a high-gain antenna
Answer: B

10. What factors affect the distance that an RF signal can be effectively received?
A. Transmitting station’s antenna type
B. Receiving station’s radio sensitivity
C. Fresnel zone blockage
D. Power over Ethernet (PoE) usage
E. Antenna connector type
F. Distance between access points
Answer: ABC

11. What factors are required to establish a high quality 2.4 GHz point-to-point RF link at a distance of 3 miles (5 kilometers)?
A. Accurate Link Budget calculations
B. Accurate Earth Bulge calculations
C. System Operating Margin (SOM) of at least 20 dB
D. A minimum antenna gain of 13 dBi
E. A Fresnel Zone that is at least 60% clear of obstructions
Answer: AE

12. Given: A 802.11 WLAN transmitter that emits an 80 mW signal is connected to a cable with 3 dB loss. The cable is connected to an antenna with a 16 dBi gain.
What is the resultant antenna power output (EIRP)?
A. 160 mW
B. 320 mW
C. 800 mW
D. 1200 mW
E. 1600 mW
Answer: E

Recommended Training about CWNP PW0-104 testing Fromat

The following courses are the recommended training for PW0-104 PDF Fromat.

PW0-104 Q & A with Explanations

PW0-104 Audio video download

PW0-104 Study Guide materials

PW0-104 Preparation Labs

PW0-104 paper books

PW0-104 rapidshare 4shared sadikhov links

PW0-104 torrent notes

PW0-104 TestInside

PW0-104 sample print pdf version

Why do you Choose PassQuick PW0-104 Test Engine?

Quality and Value for the PW0-104 Exam

PassQuick Practice Exams for CWNP Certification PW0-104 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass PW0-104 Exam

If you prepare for PW0-104 exam using our PassQuick exams, we guarantee your success in the first attempt. If you do not pass the PW0-104 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

　
　
Exam : CENP PW0-300
Title : Certified Wireless Network Expert

1. A QoS STA obtains a TXOP for an access category (AC) after what two parameters are met?
A. After a scheduled service period ends
B. The medium is idle at the AIFS[AC] slot boundary
C. The backoff time for that AC has expired
D. After a Block ACK Response
E. After a Target Beacon Transmission Time (TBTT)
Answer: BC

2. Given: An ingress frame arrives on the Ethernet port of an autonomous AP marked with an IEEE 801D user priority value.
Which IEEE 802.1D user priority values (by name) will assure the data payload carried by the Ethernet frame gets assigned to the highest priority WMM queue?
A. Controlled Load
B. Network Control
C. Video
D. Voice
E. Best Effort
F. Excellent Effort
Answer: BD

3. When using a protocol analyzer to capture conversations over a WLAN, you may often encounter encrypted data frames. Most WLAN protocol analyzers have a feature that allows the analyst to save and reload the captured frames into memory at a later time. Using this functionality, what task can be performed?
A. When IEEE 802.1X/LEAP is being used as the WLAN security mechanism, the authentication response frame can be replayed from a saved trace file at a later time to successfully authenticate a hacker.
B. If a user name and password for an IEEE 802.1X/EAP-TTLS security implementation can be obtained through social engineering tactics, the user name and password can be entered into the analyzer to decrypt the frames from a saved trace file.
C. An analyst can search through the captured frames looking for RADIUS frames that will disclose the user’s password.
D. Encrypted frames may be decrypted offline, after they are captured, by entering a WEP key or WPA passphrase into the analyzer.
Answer: D

4. How long, in microseconds, is the required Slot Time announced by an AP in an ERP BSS when both HR-DSSS and ERP-OFDM client stations are associated to the AP?
A. 2
B. 4
C. 9
D. 10
E. 20
Answer: E

5. In a Split MAC wireless network architecture, lightweight APs map user priorities (UPs) specified by the QoS STA on incoming frames to ___________.
A. IEEE 802.1D Frame Precedence Values
B. GRE Priority Bits
C. IEEE 802.1Q Tag Protocol Identifiers
D. IP Differentiated Services Code Points
E. QoS Control Header Values
Answer: D

6. According to the IEEE 802.11 standard (as amended), transmit power information is carried in which frames?
A. TPC Report frame
B. ADDTS Response frame
C. Probe Response frame
D. Beacon frame
E. Channel Switch Announcement frame
F. Measurement Report frame
Answer: ACD

7. Given: When the delayed Block Ack policy is used between two QoS STAs, the recipient must respond to a BlockAckReq frame with an ACK frame. The recipient must then send its BlockAck response frame in a subsequently obtained TXOP.
Once the contents of the BlockAck frame have been prepared, the recipient must _______________.
A. Send the BlockAck response frame to the originator in the earliest possible TXOP using the highest priority AC.
B. Send an ATIM to the originator signifying that the BlockAck response frame is ready for transmission.
C. Include the TID of the BlockAckReq in the next TXOP Request to the HC.
D. Wait for one PIFS after the next Beacon and transmit the BlockAck response to the originator using the same AC as the BlockAckReq frame.
Answer: A

8. The IEEE 802.11 standard allows for frame fragmentation. Which two fields in the IEEE 802.11 frame are involved in numbering data frame fragments and notifying the receiving station when all of the fragments of a data frame have been received?
A. Capability Information field
B. Frame Control field
C. ERP Information field
D. Sequence Control field
E. DS Parameter field
F. Ordered Service field
Answer: BD

PassQuick PW0-300 Practice Exams Description

Exam Number/Code: PW0-300

Exam Name: Certified Wireless Network Expert

VUE Code: PW0-300

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-300 exam? Searching PW0-300 Braindumps, CWNP PW0-300 Test Questions, PW0-300 Practice Exam, PW0-300 Dumps? PassQuick PW0-300 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-300 Dumps is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

CWNP PW0-300 Exam

　
　
Exam : CENP PW0-050
Title : Wireless#

1. In an 802.11 wireless LAN, what term is used to describe the wireless network name?
A. BSSID
B. ATIM
C. DIFS
D. SSID
E. FHSS
Answer: D

2. Which wireless technology supports both line-of-sight (LoS) and non-LoS connectivity?
A. ZigBee
B. WiMAX
C. Wi-Fi
D. Infrared
E. Bluetooth
Answer: B

3. 802.11a compliant wireless LAN systems use which frequency bands?
A. 2.4 GHz ISM band
B. 5.2 GHz U-NII band
C. 5.3 GHz U-NII band
D. 900 MHz ISM band
E. 5.7 GHz ISM band
Answer: BC

4. The 802.16-2004 standard, supported by the WiMAX interoperability initiative, supports which features?
A. Client mobility
B. 802.16e compatibility
C. Quality of Service (QoS)
D. Strong security
E. Ad Hoc client networking
Answer: CD

5. Which wireless data technology would have its data rate most negatively impacted by bright sunlight?
A. WiMAX
B. MIMO
C. Bluetooth
D. Wi-Fi
E. Infrared
Answer: E

6. What is the maximum speed of IrDA compliant serial infrared (SIR)?
A. 19.2 Kbps
B. 57.6 Kbps
C. 115.2 Kbps
D. 1.152 Mbps
E. 4 Mbps
Answer: C

7. Bluetooth devices use which spread spectrum technology?
A. Frequency Hopping Spread Spectrum (FHSS)
B. Direct Sequence Spread Spectrum (DSSS)
C. Orthogonal Frequency Division Multiplexing (OFDM)
D. Infrared Spread Spectrum (ISS)
Answer: A

8. A ZigBee network can scale to how many nodes?
A. 2,000
B. 10,000
C. 42,000
D. 65,000
E. 78,000
Answer: D

PassQuick PW0-050 Practice Exams Description

Exam Number/Code: PW0-050

Exam Name: Wireless#

VUE Code: PW0-050

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-050 exam? Searching PW0-050 Braindumps, CWNP PW0-050 Test Questions, PW0-050 Practice Exam, PW0-050 Dumps? PassQuick PW0-050 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-050 Dumps is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

CWNP PW0-050 Exam

　
　
Exam : CENP PW0-100
Title : certified wireless network administrator(cwna)

1. What factors affect the propagation distance of an RF signal?
A. Antenna gain
B. Receiving station sensitivity
C. Fresnel zone blockage
D. Power over Ethernet (PoE) usage
E. Antenna polarization
F. Link budget calculations
Answer: AC

2. While working on a presentation document in a conference room equipped with a wireless network, you notice that, as you turn your laptop in different directions, your wireless signal strength changes. What RF signal property is primarily responsible for this change in signal strength?
A. The RF signal’s amplitude is changing due to a change in the visual line-of-sight.
B. The RF signal’s wavelength is being affected by varying antenna gain.
C. The RF signal’s multipath is changing the amount of RF absorbed by nearby objects.
D. The RF signal’s phase is oscillating due to electromagnetic interference (EMI).
E. The RF signal’s polarization is different than the receiving antenna.
Answer: E

3. Given: XYZ Corporation is experiencing connectivity problems with their existing building-to-building bridge link. A brick wall on the roof of one building is partially blocking the Fresnel Zone, and the connection is dropping many frames. The administrator moves the antenna to an area not obstructed by the brick wall and then realizes the RF cable cannot reach the new location.
If an RF extension cable is used, what are the likely results?
A. The data throughput rate will increase because VSWR will decrease.
B. The Equivalent Isotropically Radiated Power (EIRP) will decrease.
C. The antenna coverage area will decrease.
D. The return loss will increase unless the impedance of the RF extension cable is equal to 50% of the antenna impedance.
E. The likelihood of a direct lightning strike will increase, placing the entire WLAN system at risk.
Answer: BC

4. Which units of measure are used to describe a calculable power quantity?
A. dB
B. dBm
C. dBi
D. mW
E. RSSI
F. dBd
Answer: BD

5. What phrase describes the effect of increasing the distance that an RF wave travels when the RF antenna lobe is focused in a desired direction?
A. Polar Extension
B. Active Amplification
C. Beam Compression
D. Passive Gain
E. Phased Array Propagation
Answer: D

6. In a long-distance RF link, what statement about Fade Margin is true?
A. Fade Margin is the amount of signal strength in addition to the Link Budget.
B. The Fade Margin of a long-distance RF link does not account for antenna gain.
C. Fade Margin is rarely taken into account on a long-distance RF link.
D. Fade Margin and Jamming Margin are synonymous, interchangeable terms.
Answer: A

7. What is a valid type of lightning arrestor used with 802.11 wireless LANs?
A. Coaxial arrestor with a metal oxide varistor (MOV) input circuit
B. Parallel tuned tank-circuit arrestor
C. Coaxial arrestor with a gas discharge tube
D. Inductor-based load-sensing arrestor
Answer: C

8. Given: ABC University provides wireless access to campus buildings from their Data Center building. ABC has installed a tower on the Data Center building with a sectorized omnidirectional antenna array using 90 of horizontal beamwidth per sector.
What is the next step in configuring the antenna array?
A. Calculate Earth Bulge into the System Operating Margin (SOM).
B. Configuring the downtilt of each antenna in the array.
C. Providing DC power to each antenna in the array.
D. Adjusting each antenna’s beamwidths for optimal gain.
Answer: B

PassQuick PW0-100 Practice Exams Description

Exam Number/Code: PW0-100

Exam Name: certified wireless network administrator(cwna)

VUE Code: PW0-100

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-100 exam? Searching PW0-100 Braindumps, CWNP PW0-100 Test Questions, PW0-100 Practice Exam, PW0-100 Dumps? PassQuick PW0-100 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-100 Dumps is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

CWNP PW0-100 Exam

PassQuick PW0-070 Practice Exams Description

Exam Number/Code: PW0-070

Exam Name: Certified Wireless Technology Specialist

VUE Code: PW0-070

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-070 exam? Searching PW0-070 Braindumps, CWNP PW0-070 Test Questions, PW0-070 Practice Exam, PW0-070 Dumps? PassQuick PW0-070 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-070 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Recommended Training about CWNP PW0-070 testing Fromat

The following courses are the recommended training for PW0-070 PDF Fromat.

PW0-070 Q & A with Explanations

PW0-070 Audio video download

PW0-070 Study Guide materials

PW0-070 Preparation Labs

PW0-070 paper books

PW0-070 rapidshare 4shared sadikhov links

PW0-070 torrent notes

PW0-070 TestInside

PW0-070 sample print pdf version

Why do you Choose PassQuick PW0-070 Test Engine?

Quality and Value for the PW0-070 Exam

PassQuick Practice Exams for CWNP Certification PW0-070 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass PW0-070 Exam

If you prepare for PW0-070 exam using our PassQuick exams, we guarantee your success in the first attempt. If you do not pass the PW0-070 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

　
　
Exam : CENP PW0-200
Title : Certified Wireless Security Professional(CWSP)

1. In this diagram illustrating an example of the IEEE 802.11 standard’s 4-Way Handshakewhat is the purpose of the ANonce and SNonce?
A. They are used to pad Message 1 and Message 2 so there is no empty space in the frame.
B. The IEEE 802.11 standard requires that all cryptographic frames contain a nonce for security purposes.
C. They are added together and used as the GMKfrom which the GTK is derived.
D. They are values used in the derivation of the Pairwise Transient Key.
Answer: D

2. What WIPS parameter is configured to generate notifications?
A. Mobile unit density violations
B. Admission control status
C. Sensor sensitivity levels
D. Policy threshold values
Answer: D

3. What policies would prevent peer-to-peer attacks against wireless-enabled corporate laptop computers when the laptops are also used on public access networks such as wireless hotspots?
A. Require managed personal firewall software on each laptop.
B. Require secure applications such as POP3/SHTTPSand SSH2.
C. Require VPN software for connectivity to the corporate network.
D. Require WPA2-Enterprise as the minimal WLAN security solution.
E. Require Port Address Translation (PAT) on each laptop.
F. Require a managed wireless endpoint security agent on each laptop.
Answer: ABCF

4. Given: A network security auditor is assessing an IEEE 802.11 network’s exposure to security holes.
What task would save the most time if performed before the audit?
A. Identify the IP subnet information for each network segment.
B. Identify the manufacturer of the wireless intrusion prevention system.
C. Identify the skill level of the wireless network security administrator(s).
D. Identify the manufacturer of the wireless infrastructure hardware.
E. Identify the wireless security solution(s) currently in use.
Answer: E

5. What happens in a bit flipping attack against an IEEE 802.11 device?
A. An attacker captures an encrypted framemodifies the ciphertextmodifies the ICV to hide the change to the ciphertextand then transmits the frame to appear as if it is from the original source.
B. An attacker uses a non-linear Message Integrity Check (MIC) on his computer to form a wireless crossover connection with the target computer.
C. An attacker injects data into a wireless transmission that results in a memory access exception at the target system for the purpose of breaching security.
D. An attacker sends each frame with the first bit alternating between 0 and 1causing the target computer to disable encryption synchronization.
E. An attacker captures an encrypted authentication frameand then executes a cracking algorithm against each 0 and 1 in the frame. After the frame is crackedit is used to authenticate the attacker’s computer.
Answer: A

6. Given: John Smith often works from home and wireless hotspots rather than commuting to the office. His laptop connects to the office network over IEEE 802.11 WLANs.
To safeguard his datawhat wireless security policy items should be implemented?
A. Use an IPSec VPN for remote connectivity
B. Use an HTTPS captive portal for authentication at hotspots
C. Use personal firewall software on his laptop
D. Use a protocol analyzer on his laptop to monitor for risks
E. Use 802.1X/PEAPv0 to connect to the corporate office network
Answer: AC

7. Given: ABC Company has a WLAN controller with three access points15 client devicesand uses WPA2-Personal for WLAN security.
What statement about ABC Company’s WLAN security is true?
A. Intruders may obtain the passphrase with an offline dictionary attack and gain network accessbut will be unable to decrypt data traffic.
B. Traffic injection attacks are possible because the transmitter lacks frame numbering.
C. An unauthorized wireless client device cannot associatebut can eavesdrop on some data because WPA2-Personal does not encrypt broadcast traffic.
D. An authorized WLAN user with a protocol analyzer can decode data frames of other authorized users if he captures that user’s 4-Way Handshake.
E. Because WPA2-Personal uses Open System authentication followed by a 4-Way Handshakehijacking attacks are easily performed.
Answer: D

8. Given: You have a laptop computer with an integrated Wi-Fi compliant MiniPCI card.
What statements describe the limited effectiveness of locating rogue access points using WLAN discovery software such as NetStumblerKismetor MacStumbler?
A. Discovery tools like those listed cannot determine the authorization status of an access point.
B. A laptop computer can only be in one location at a time.
C. Discovery tools like those listed cannot determine if an access point is attached to a wired network.
D. Rogue access points using non-IEEE 802.11 frequency bands or unpopular modulations are not detected.
E. When data encryption in useaccess points cannot be detected using discovery tools like those listed.
Answer: ABCD

PassQuick PW0-200 Practice Exams Description

Exam Number/Code: PW0-200

Exam Name: certified wireless security professional(cwsp)

VUE Code: PW0-200

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-200 exam? Searching PW0-200 Braindumps, CWNP PW0-200 Test Questions, PW0-200 Practice Exam, PW0-200 Dumps? PassQuick PW0-200 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-200 Dumps is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

CWNP PW0-200 Exam

　
　
Exam : CWNP PW0-104
Title : Wireless LAN Administration Exam

1. What factors affect the distance that an RF signal can be effectively received?
A. Transmitting station’s antenna type
B. Receiving station’s radio sensitivity
C. Fresnel zone blockage
D. Power over Ethernet (PoE) usage
E. Antenna connector type
F. Distance between access points
Answer: ABC

2. Given: A WLAN transmitter that emits a 200 mW signal is connected to a cable with a 9 dB loss.
if the cable is connected to an antenna with a 10 dBi gain, what is the EIRP at the antenna element?
A. 50 mW
B. 250 mW
C. 500 mW
D. 750 mW
E. 1000 mW
Answer: B

3. Given: ABC Company’s network administrator was just asked to install a 5 GHz OFDM bridge link between two buildings. He connected a WLAN bridge with a 50-ohm output to a 50-ohm RF coaxial cable. He connected the other end of the RF coaxial cable to a 25-ohm, 6 dBi Yagi antenna.
What is the maximum VSWR between the WLAN bridge and the Yagi antenna?
A. 1.0:1
B. 1.1:1
C. 1.2:1
D. 1.5:1
E. 2.0:1
F. 1.0:2
Answer: E

4. Given: Return Loss is the decrease of forward energy in a system because some of the power is being reflected back toward the transmitter.
What can cause a high return loss in an RF transmission system?
A. A Voltage Standing Wave Ratio (VSWR) of 1.5:1
B. An impedance mismatch between devices in the RF system
C. Cross-polarization of the RF signal as it passes through the RF system
D. The use of multiple connector types in the RF system (e.g. N-type and SMA-type)
E. Low output power at the transmitter and use of a high-gain antenna
Answer: B

5. What causes an excessively high Voltage Standing Wave Ratio (VSWR) in an 8011 WLAN?
A. An impedance mismatch between devices in series with the main RF signal
B. Reflected DC voltage on the main RF signal line
C. Refracted RF signal peaks along the main signal path
D. Crosstalk (inductance) between adjacent conductors
Answer: A

6. What word describes the bending of an RF signal as it passes between mediums of different density?
A. Diffraction
B. Reflection
C. Refraction
D. Diffusion
E. Scattering
Answer: C

7. As an RF wave propagates through space, the wave front experiences natural expansion. What is the detrimental effect of this expansion in a WLAN system?
A. Linear Diffusion Loss
B. Signal Attenuation
C. Transmission Obfuscation
D. Fresnel Zone Thinning
E. Azimuth Inflation
Answer: B

8. What factor is NOT taken into account when calculating the System Operating Margin of a point-to-point outdoor WLAN bridge link?
A. Operating frequency
B. Tx antenna gain
C. Tx power
D. Rx cable loss
E. Antenna height
F. Rx sensitivity
G. Distance
Answer: E

PassQuick PW0-104 Practice Exams Description

Exam Number/Code: PW0-104

Exam Name: Wireless LAN Administration Exam

VUE Code: PW0-104

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-104 exam? Searching PW0-104 Braindumps, CWNP PW0-104 Test Questions, PW0-104 Practice Exam, PW0-104 Dumps? PassQuick PW0-104 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-104 Dumps is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

CWNP PW0-104 Exam

PassQuick PW0-050 Practice Exams Description

Exam Number/Code: PW0-050

Exam Name: Wireless#

VUE Code: PW0-050

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-050 exam? Searching PW0-050 Braindumps, CWNP PW0-050 Test Questions, PW0-050 Practice Exam, PW0-050 Dumps? PassQuick PW0-050 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-050 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Free PassQuick PW0-050 Practice Engine Demo Download

Download CWNP PW0-050 Pdf Exam

　
　
Exam : CENP PW0-050
Title : Wireless#

1. Bluetooth devices use which spread spectrum technology?
A. Frequency Hopping Spread Spectrum (FHSS)
B. Direct Sequence Spread Spectrum (DSSS)
C. Orthogonal Frequency Division Multiplexing (OFDM)
D. Infrared Spread Spectrum (ISS)
Answer: A

2. The 802.16-2004 standard, supported by the WiMAX interoperability initiative, supports which features?
A. Client mobility
B. 802.16e compatibility
C. Quality of Service (QoS)
D. Strong security
E. Ad Hoc client networking
Answer: CD

3. What is the maximum speed of IrDA compliant serial infrared (SIR)?
A. 19.2 Kbps
B. 57.6 Kbps
C. 115.2 Kbps
D. 1.152 Mbps
E. 4 Mbps
Answer: C

4. 802.11a compliant wireless LAN systems use which frequency bands?
A. 2.4 GHz ISM band
B. 5.2 GHz U-NII band
C. 5.3 GHz U-NII band
D. 900 MHz ISM band
E. 5.7 GHz ISM band
Answer: BC

5. What wireless industry organization implements certification testing to assure interoperability of wireless LAN hardware complying with the 802.11-1999 standard and related amendments?
A. WiMAX Forum
B. Wi-Fi Alliance
C. Infrared Data Association
D. IEEE
E. Bluetooth SIG
Answer: B

6. Which wireless data technology would have its data rate most negatively impacted by bright sunlight?
A. WiMAX
B. MIMO
C. Bluetooth
D. Wi-Fi
E. Infrared
Answer: E

7. Which wireless LAN standard specifies the use of Direct Sequence Spread Spectrum technology?
A. 802.11a
B. 802.11b
C. 802.16
D. 802.3af
E. 802.15.1
Answer: B

8. Which wireless industry organization is described as, an association of companies working together to enable reliable, cost-effective, low-power, wirelessly networked, monitoring and control products based on an open global standard.?
A. Wi-Fi Alliance
B. Bluetooth SIG
C. ZigBee Alliance
D. WiMAX Forum
E. IrDA
Answer: C

9. Which wireless technology supports both line-of-sight (LoS) and non-LoS connectivity?
A. ZigBee
B. WiMAX
C. Wi-Fi
D. Infrared
E. Bluetooth
Answer: B

10. A ZigBee network can scale to how many nodes?
A. 2,000
B. 10,000
C. 42,000
D. 65,000
E. 78,000
Answer: D

11. In an 802.11 wireless LAN, what term is used to describe the wireless network name?
A. BSSID
B. ATIM
C. DIFS
D. SSID
E. FHSS
Answer: D

12. The IEEE 802.16e standard supports frequencies in what range?
A. 2.5 3.5 GHz
B. 2.4 5.7 GHz
C. 2 11 GHz
D. 6 12 GHz
Answer: C

Recommended Training about CWNP PW0-050 testing Fromat

The following courses are the recommended training for PW0-050 PDF Fromat.

PW0-050 Q & A with Explanations

PW0-050 Audio video download

PW0-050 Study Guide materials

PW0-050 Preparation Labs

PW0-050 paper books

PW0-050 rapidshare 4shared sadikhov links

PW0-050 torrent notes

PW0-050 TestInside

PW0-050 sample print pdf version

Why do you Choose PassQuick PW0-050 Test Engine?

Quality and Value for the PW0-050 Exam

PassQuick Practice Exams for CWNP Certification PW0-050 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass PW0-050 Exam

If you prepare for PW0-050 exam using our PassQuick exams, we guarantee your success in the first attempt. If you do not pass the PW0-050 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

PassQuick PW0-300 Practice Exams Description

Exam Number/Code: PW0-300

Exam Name: Certified Wireless Network Expert

VUE Code: PW0-300

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-300 exam? Searching PW0-300 Braindumps, CWNP PW0-300 Test Questions, PW0-300 Practice Exam, PW0-300 Dumps? PassQuick PW0-300 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-300 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Free PassQuick PW0-300 Practice Engine Demo Download

Download CWNP PW0-300 Pdf Exam

　
　
Exam : CENP PW0-300
Title : Certified Wireless Network Expert

1. Many autonomous access points support IEEE 802.1Q VLAN tagging. When analyzing a WLAN system using IEEE 802.1Q tags, where can the VLAN tag number be seen?
A. In the Sequence Control field of the MSDU
B. In the PLCP header’s Service field
C. In the Frame Control field of the MPDU header
D. In the Ethernet header on the wired port of the access point
E. In the Beacon Management frame’s Capabilities fixed field
Answer: D

2. How long, in microseconds, is the required Slot Time announced by an AP in an ERP BSS when both HR-DSSS and ERP-OFDM client stations are associated to the AP?
A. 2
B. 4
C. 9
D. 10
E. 20
Answer: E

3. Given: ABC Company is implementing a QoS enabled infrastructure that will support both voice and data. The WLAN controller is connected to one of three core layer-3 Ethernet switches. Each core layer-3 Ethernet switch has multiple edge layer-2 Ethernet switches attached. Lightweight APs are connected to all edge layer-2 Ethernet switches. The WLAN controller is on subnet 10.1.1.0/24, and the APs are on numerous other subnets. The APs are connected to the WLAN controller via LWAPP tunnels.
When IEEE 802.11 frames arrive at a lightweight AP from a QoS STA that need to be sent to the WLAN controller, which bits can the AP mark to signal the layer-2 and layer-3 Ethernet switches to use higher priority processing?
A. The Ethernet frame’s 802.1Q priority tag bits
B. The IP header’s TOS bits
C. The IEEE 802.11 frame’s QoS Control bits
D. The LWAPP header’s C bit
E. The UDP header’s PRI bits
Answer: AB

4. What events will cause an established TSPEC to be deleted by a AP?
A. Disassociation of the non-AP QoS STA using the TSPEC from the QoS BSS
B. Traffic Stream inactivity timeout
C. Reassociation of the non-AP QoS STA with another QoS AP
D. Receipt of a DELBA frame from a non-AP QoS STA
E. Receipt of an Update TSPEC frame from a non-AP QoS STA
F. A Controlled Access Phase (CAP) burst
Answer: ABC

5. Given: When the delayed Block Ack policy is used between two QoS STAs, the recipient must respond to a BlockAckReq frame with an ACK frame. The recipient must then send its BlockAck response frame in a subsequently obtained TXOP.
Once the contents of the BlockAck frame have been prepared, the recipient must _______________.
A. Send the BlockAck response frame to the originator in the earliest possible TXOP using the highest priority AC.
B. Send an ATIM to the originator signifying that the BlockAck response frame is ready for transmission.
C. Include the TID of the BlockAckReq in the next TXOP Request to the HC.
D. Wait for one PIFS after the next Beacon and transmit the BlockAck response to the originator using the same AC as the BlockAckReq frame.
Answer: A

6. Given: ABC Company has implemented a QoS capable IEEE 802.11 WLAN controller based network with lightweight access points as shown in the graphic.
What is the advantage of the access point mapping IEEE 802.11 user priority (UP) values to DSCP values in the IP header that encapsulates the 802.11 frame?
A. Direct mapping of UP-to-DSCP values increases effective throughput between the access point and WLAN controller.
B. Since UP-to-802.1Q PCP mappings are not possible at the access point, the only method of prioritizing upstream data is through UP-to-DSCP mappings.
C. The QoS markings will survive layer 2 hops that could remove 802.1Q PCP values.
D. UP-to-DSCP mappings are more granular than UP-to-802.1Q PCP mappings.
Answer: C

7. Given: An ingress frame arrives on the Ethernet port of an autonomous AP marked with an IEEE 801D user priority value.
Which IEEE 802.1D user priority values (by name) will assure the data payload carried by the Ethernet frame gets assigned to the highest priority WMM queue?
A. Controlled Load
B. Network Control
C. Video
D. Voice
E. Best Effort
F. Excellent Effort
Answer: BD

8. The IEEE 802.11 standard allows for frame fragmentation. Which two fields in the IEEE 802.11 frame are involved in numbering data frame fragments and notifying the receiving station when all of the fragments of a data frame have been received?
A. Capability Information field
B. Frame Control field
C. ERP Information field
D. Sequence Control field
E. DS Parameter field
F. Ordered Service field
Answer: BD

9. A QoS STA obtains a TXOP for an access category (AC) after what two parameters are met?
A. After a scheduled service period ends
B. The medium is idle at the AIFS[AC] slot boundary
C. The backoff time for that AC has expired
D. After a Block ACK Response
E. After a Target Beacon Transmission Time (TBTT)
Answer: BC

10. In a Split MAC wireless network architecture, lightweight APs map user priorities (UPs) specified by the QoS STA on incoming frames to ___________.
A. IEEE 802.1D Frame Precedence Values
B. GRE Priority Bits
C. IEEE 802.1Q Tag Protocol Identifiers
D. IP Differentiated Services Code Points
E. QoS Control Header Values
Answer: D

11. According to the IEEE 802.11 standard (as amended), transmit power information is carried in which frames?
A. TPC Report frame
B. ADDTS Response frame
C. Probe Response frame
D. Beacon frame
E. Channel Switch Announcement frame
F. Measurement Report frame
Answer: ACD

12. When using a protocol analyzer to capture conversations over a WLAN, you may often encounter encrypted data frames. Most WLAN protocol analyzers have a feature that allows the analyst to save and reload the captured frames into memory at a later time. Using this functionality, what task can be performed?
A. When IEEE 802.1X/LEAP is being used as the WLAN security mechanism, the authentication response frame can be replayed from a saved trace file at a later time to successfully authenticate a hacker.
B. If a user name and password for an IEEE 802.1X/EAP-TTLS security implementation can be obtained through social engineering tactics, the user name and password can be entered into the analyzer to decrypt the frames from a saved trace file.
C. An analyst can search through the captured frames looking for RADIUS frames that will disclose the user’s password.
D. Encrypted frames may be decrypted offline, after they are captured, by entering a WEP key or WPA passphrase into the analyzer.
Answer: D

Recommended Training about CWNP PW0-300 testing Fromat

The following courses are the recommended training for PW0-300 PDF Fromat.

PW0-300 Q & A with Explanations

PW0-300 Audio video download

PW0-300 Study Guide materials

PW0-300 Preparation Labs

PW0-300 paper books

PW0-300 rapidshare 4shared sadikhov links

PW0-300 torrent notes

PW0-300 TestInside

PW0-300 sample print pdf version

Why do you Choose PassQuick PW0-300 Test Engine?

Quality and Value for the PW0-300 Exam

PassQuick Practice Exams for CWNP Certification PW0-300 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass PW0-300 Exam

If you prepare for PW0-300 exam using our PassQuick exams, we guarantee your success in the first attempt. If you do not pass the PW0-300 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

PassQuick PW0-070 Practice Exams Description

Exam Number/Code: PW0-070

Exam Name: Certified Wireless Technology Specialist

VUE Code: PW0-070

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-070 exam? Searching PW0-070 Braindumps, CWNP PW0-070 Test Questions, PW0-070 Practice Exam, PW0-070 Dumps? PassQuick PW0-070 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-070 Dumps is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

CWNP PW0-070 Exam

PassQuick PW0-205 Practice Exams Description

Exam Number/Code: PW0-205

Exam Name: certified wireless analusis professional(cwap)

VUE Code: PW0-205

vendor:CWNP

Exam Language(s): English

Certification: CWNP practice test

Preparing for the PW0-205 exam? Searching PW0-205 Braindumps, CWNP PW0-205 Test Questions, PW0-205 Practice Exam, PW0-205 Dumps? PassQuick PW0-205 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick PW0-205 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Free PassQuick PW0-205 Practice Engine Demo Download

Download CWNP PW0-205 Pdf Exam

　
　
Exam : CENP PW0-205
Title : certified wireless analusis professional(cwap)

1. An 802.11b client station, sends a single 600 byte MSDU to another 802.11b client station while operating as part of an unsecured infrastructure BSS. Due to thresholds set on all client stations and the access point, all MPDUs over 300 bytes in length invoke the RTS/CTS protocol. How many individual CTS frames are transmitted on the wireless medium as part of the entire process of moving the 600 byte MSDU between the two client stations?
A. 1
B. 2
C. 3
D. 4
Answer: B

2. When the ToDS bit is set to 1 and the FromDS bit is set to 0 in the Frame Control field of an 802.11 Data frame, what might this indicate about the infrastructure and the wireless conversation?
A. A wireless client station could be sending data to a wired station through an access point.
B. A wireless client station must be sending data to a wireless station where the frame has to traverse a Wireless Distribution System (WDS).
C. A wireless client station must be sending data directly to the access point for the purpose of managing the access point.
D. A wireless client station could be sending data to a wireless client station across an access point.
E. A wireless client station could be sending data directly to another wireless client station as part of an IBSS.
Answer: AD

3. Which of the following descriptions accurately describes IEEE 802.11 compliant Power Save mode operation in a DCF Basic Service Set?
A. Following a period of time in a low power state, client stations wake themselves and automatically poll the access point for traffic using a PS-Poll frame.
B. When the access point’s buffer is full, the access point wakes all client stations using a PS-Poll frame so that they can receive the data.
C. Upon receiving traffic for a dozing station, the access point wakes the client station using a PS-Poll frame so that the client station can receive the data.
D. After waking from a low power state, client stations listen for the next beacon to determine if sending a PS-Poll frame to the access point is necessary.
E. After waking at a schedule TBTT, client stations automatically send Null Function frames to the access point with the Power Management bit cleared.
Answer: D

4. Choose the true statements regarding wireless network discovery processes for an 802.11b network.
A. Client stations may continually send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner, regardless of their association state.
B. Access points send Beacon Management frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner including the channel for which the access point is configured.
C. Client stations send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner until they associate with an access point. After associating to an access point, they are no longer allowed to transmit Probe Request frames.
D. Access points send Beacon Management frames only on the 802.11b channel in the 2.4 GHz ISM band for which the access point is configured.
E. Client stations send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner until they receive at least 3 Probe Response frames.
Answer: AD

5. The 802.11 series of standards calls for use of a Traffic Indication Map (TIM) and a Delivery Traffic Indication Message (DTIM). Which of the following is true regarding the TIM and DTIM in an infrastructure BSS?
A. The TIM is a field in the Beacon Management frame that holds a map of every client station associated to an access point. It is used for broadcast traffic delivery.
B. The TIM and DTIM are both part of the Beacon management frame and are both sent in every Beacon for the purpose of announcing the modulation type and supported rate set of the access point.
C. The DTIM parameters are part of each Beacon’s TIM Information Element, and they are used to indicate queued broadcast/multicast data to client stations using power management features in the BSS.
D. The DTIM is used in 802.11a and 802.11g Beacons whereas the TIM is used only in 802.11b Beacons. The DTIM purpose is to allow for higher rates of Beacon broadcasting and thus raise overall data rates in OFDM based systems.
E. A DTIM period of 0 means that every TIM is a DTIM.
F. The first Beacon sent during a CFP must contain a DTIM
Answer: CF

6. Which of the following is true regarding frame acknowledgement in an 802.11 wireless LAN?
A. ACK frames following Data fragments set the NAV of competing stations for a duration equal to two SIFS plus the next Data fragment and its ACK.
B. A client station reassociation request frames are only acknowledged with a reassociation response from the access point when roaming in a wireless LAN secured with 802.1X/EAP.
C. Probe request acknowledgement (sending of a probe response) is configurable in the access point and is always linked to SSID broadcast configuration in Beacons.
D. Beacon frames are acknowledged by all client stations configured for PCF mode.
E. Frame fragments are acknowledged individually (with an ACK frame)
F. In PCF mode, WEP-Data frames are only acknowledged by client stations, never by access points.
Answer: AE

7. The Timestamp field, found in 8011 Beacon Management frames, is 8 bytes in length and serves which of the following purposes?
A. Keeps all client stations in a BSS synchronized to within approximately 4 microseconds of the access point.
B. Allows client stations in the IBSS to pick the best of multiple beacons.
C. Used to notify client stations using power management features of how long their queued frames have been held by the access point.
D. Informs associating client stations how often to expect Beacon Management frames to be sent by the access point.
E. Allows all client stations in a BSS to calculate how long it took for the Beacon Management frame to traverse the wireless medium.
Answer: AB

8. Which is true of the Association Identifier (AID) used in 802.11 wireless LANs?
A. The AID has a maximum value of 2048, and is used to uniquely identify a wireless client station associated with an access point.
B. The AID has a maximum value of 2007, and resides in the duration/ID field of a PS-Poll frame only.
C. When bit 16 of the field is zero, the value in bits 15-0 represent the remaining duration of a frame exchange.
D. The least significant 8 bits of this field are used by the wireless client station to identify which bit in a TIM indicates that the access point has frames buffered for the wireless client station.
E. The AID is used by the access point in DCF mode to reduce duplicate transmissions when sending multicasts.
Answer: B

9. When RTS/CTS is used in DCF mode, what is the frame exchange sequence between two wireless stations including interframe spaces?
A. DIFS-RTS-SIFS-CTS-SIFS-DATA-SIFS-ACK
B. DIFS-RTS-ACK-CTS-ACK-DATA-SIFS-ACK
C. DIFS-RTS-CTS-SIFS-ACK-DATA-SIFS-ACK
D. EIFS-RTS-CTS-SIFS-DATA-SIFS-ACK
E. PIFS-RTS-SIFS-CTS-SIFS-DATA-SIFS-ACK
Answer: A

10. When using a wireless protocol analyzer, it is common to see Beacon Management frames (Beacons) being sent several times per second. Which of the following statements is true regarding Beacons?
A. Beacons can be disabled for security purposes.
B. The BSSID and Source Address are always the same.
C. The Destination address is always FF:FF:FF:FF:FF:FF.
D. The Receiver address and the BSSID are always the same.
E. The reason Beacons are transmitted so often is that they are unicast frames destined to each associated station.
F. The 802.11 standard specifies that all Beacons must contain a DTIM information element.
Answer: BC

11. When an access point sends an RTS frame, the duration field will contain an amount of time, measured in microseconds, equal to which of the following?
A. 2 ACK, 1 RTS, 1 DATA, 4 SIFS
B. 1 ACK, 1 CTS, 1 DATA, 3 SIFS
C. 1 DATA, 1 RTS, 2 SIFS, 1 DIFS, 1 ACK
D. 1 RTS, 1 CTS, 1 DATA, 2 ACK, 4 SIFS
Answer: B

12. A wireless network administrator has examined the frame retry counts on several client stations in a WLAN that is not using encryption, and has determined that they are extraordinarily high. For this reason, he has decided to configure station fragmentation thresholds to 400 bytes. With this configuration change, when a data frame with a 1500 byte MSDU is transmitted by one of the wireless client stations to a wired station through an access point, what will be the order and size (in bytes) of the fragments as they’re transmitted?
A. Frame1 = 400, Frame2 = 400, Frame3 = 400, Frame4 = 300
B. Frame1 = 300, Frame2 = 300, Frame3 = 300, Frame4 = 300, Frame5 = 300
C. Frame1 = 300, Frame2 = 400, Frame3 = 400, Frame4 = 400
D. Frame1 = 400, Frame2 = 400, Frame3 = 400, Frame4 = 400, Frame5 = 40
E. The fragmentation threshold setting on client stations only affects received frames, not transmitted frames
F. The fragmentation threshold setting on client stations is not a manual adjustment, and can only be auto-configured by access points
Answer: D

Recommended Training about CWNP PW0-205 testing Fromat

The following courses are the recommended training for PW0-205 PDF Fromat.

PW0-205 Q & A with Explanations

PW0-205 Audio video download

PW0-205 Study Guide materials

PW0-205 Preparation Labs

PW0-205 paper books

PW0-205 rapidshare 4shared sadikhov links

PW0-205 torrent notes

PW0-205 TestInside

PW0-205 sample print pdf version

Why do you Choose PassQuick PW0-205 Test Engine?

Quality and Value for the PW0-205 Exam

PassQuick Practice Exams for CWNP Certification PW0-205 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass PW0-205 Exam

If you prepare for PW0-205 exam using our PassQuick exams, we guarantee your success in the first attempt. If you do not pass the PW0-205 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.